NEWS CENTER

News Center

Standardized electric vehicle assembly line design points and conventional parameters

  • Categorize:Company Dynamics
  • Author:
  • Source:
  • Release time:2019-02-22
  • pageviews:50

Summary
Standardized electric vehicle assembly line design points and conventional parameters


The standard form of electric vehicle assembly line is the chain plate conveyor line, the chain plate conveyor line has a long distance, can pull heavier items, and is suitable for the assembly process of electric vehicles. However, considering the logistics transportation, it is necessary to configure the suspended conveyor line

1. Technical requirements of electric vehicle assembly line:
A, the total length of the whole line: 30000mm(including power tightening mechanism);
B, the total width of the line body: 710mm(including the long groove);
C, line gymnastics height: 500mm(±10mm adjustable);
D, total lighting height: 2350mm(±10mm adjustable);
E, working bit length: 2200mm;
F, the number of stations: 13 positions;
G, chain plate: 500mm×200mm×2mm; The clamp chain plate adopts 3mm thick cold-rolled steel plate;
H, line body speed: 0.6m-6m /min; Continuous/beat running.

2, the main configuration of electric vehicle assembly line:

A, the top protection plate is not less than 1.0mm steel plate;
B, the top lampshade is not less than 1.0mm steel plate;
C, the top horizontal pipe 30×40mm rectangular square pipe, pipe wall thickness is not less than 1.5mm;
D, fluorescent lamp 40W per station one;
E, the top head is not less than 1.0mm steel plate;
F, the horizontal hanging adopts 40×60mm rectangular square pipe, the thickness of the pipe wall is not less than 1.5mm;
G, the frame adopts 30×40mm rectangular square pipe, the thickness of the pipe wall is not less than 1.5mm;
H, both sides of the line body are made of not less than 1.0mm steel plate;
I. A set of gas distribution pipes for the whole line (without air source);
J, the whole line with a set of tight;
K, the whole line is equipped with special domestic needle roller chain: chain pitch P=100;
L, the whole line is equipped with a control cabinet, electrical components are made in China;
M, power using Taiwan motor, frequency control;
N, each station is equipped with a 220V power socket;
O. Each pair is equipped with one swinging fan;
P, the whole line with luxury/simple electric vehicle assembly fixture;
Q, two meters upper and lower pattern steel plate ramp.

Standardized electric vehicle assembly line design points and conventional parameters

Summary
Standardized electric vehicle assembly line design points and conventional parameters


The standard form of electric vehicle assembly line is the chain plate conveyor line, the chain plate conveyor line has a long distance, can pull heavier items, and is suitable for the assembly process of electric vehicles. However, considering the logistics transportation, it is necessary to configure the suspended conveyor line

1. Technical requirements of electric vehicle assembly line:
A, the total length of the whole line: 30000mm(including power tightening mechanism);
B, the total width of the line body: 710mm(including the long groove);
C, line gymnastics height: 500mm(±10mm adjustable);
D, total lighting height: 2350mm(±10mm adjustable);
E, working bit length: 2200mm;
F, the number of stations: 13 positions;
G, chain plate: 500mm×200mm×2mm; The clamp chain plate adopts 3mm thick cold-rolled steel plate;
H, line body speed: 0.6m-6m /min; Continuous/beat running.

2, the main configuration of electric vehicle assembly line:

A, the top protection plate is not less than 1.0mm steel plate;
B, the top lampshade is not less than 1.0mm steel plate;
C, the top horizontal pipe 30×40mm rectangular square pipe, pipe wall thickness is not less than 1.5mm;
D, fluorescent lamp 40W per station one;
E, the top head is not less than 1.0mm steel plate;
F, the horizontal hanging adopts 40×60mm rectangular square pipe, the thickness of the pipe wall is not less than 1.5mm;
G, the frame adopts 30×40mm rectangular square pipe, the thickness of the pipe wall is not less than 1.5mm;
H, both sides of the line body are made of not less than 1.0mm steel plate;
I. A set of gas distribution pipes for the whole line (without air source);
J, the whole line with a set of tight;
K, the whole line is equipped with special domestic needle roller chain: chain pitch P=100;
L, the whole line is equipped with a control cabinet, electrical components are made in China;
M, power using Taiwan motor, frequency control;
N, each station is equipped with a 220V power socket;
O. Each pair is equipped with one swinging fan;
P, the whole line with luxury/simple electric vehicle assembly fixture;
Q, two meters upper and lower pattern steel plate ramp.

  • Categorize:Company Dynamics
  • Author:
  • Source:
  • Release time:2019-02-22
  • pageviews:50

Standardized electric vehicle assembly line design points and conventional parameters


The standard form of electric vehicle assembly line is the chain plate conveyor line, the chain plate conveyor line has a long distance, can pull heavier items, and is suitable for the assembly process of electric vehicles. However, considering the logistics transportation, it is necessary to configure the suspended conveyor line

1. Technical requirements of electric vehicle assembly line:
A, the total length of the whole line: 30000mm(including power tightening mechanism);
B, the total width of the line body: 710mm(including the long groove);
C, line gymnastics height: 500mm(±10mm adjustable);
D, total lighting height: 2350mm(±10mm adjustable);
E, working bit length: 2200mm;
F, the number of stations: 13 positions;
G, chain plate: 500mm×200mm×2mm; The clamp chain plate adopts 3mm thick cold-rolled steel plate;
H, line body speed: 0.6m-6m /min; Continuous/beat running.

2, the main configuration of electric vehicle assembly line:

A, the top protection plate is not less than 1.0mm steel plate;
B, the top lampshade is not less than 1.0mm steel plate;
C, the top horizontal pipe 30×40mm rectangular square pipe, pipe wall thickness is not less than 1.5mm;
D, fluorescent lamp 40W per station one;
E, the top head is not less than 1.0mm steel plate;
F, the horizontal hanging adopts 40×60mm rectangular square pipe, the thickness of the pipe wall is not less than 1.5mm;
G, the frame adopts 30×40mm rectangular square pipe, the thickness of the pipe wall is not less than 1.5mm;
H, both sides of the line body are made of not less than 1.0mm steel plate;
I. A set of gas distribution pipes for the whole line (without air source);
J, the whole line with a set of tight;
K, the whole line is equipped with special domestic needle roller chain: chain pitch P=100;
L, the whole line is equipped with a control cabinet, electrical components are made in China;
M, power using Taiwan motor, frequency control;
N, each station is equipped with a 220V power socket;
O. Each pair is equipped with one swinging fan;
P, the whole line with luxury/simple electric vehicle assembly fixture;
Q, two meters upper and lower pattern steel plate ramp.

Popular news

卓凯电子 卓凯电子

-
  • Phone:18859151762

  • Email:sales@fzzk-dcs.cn

微信咨询

WeChat

Page Copyright © 2024  Fuzhou Zhuokai Electronic Technology Co., Ltd  All rights reserved.   闽ICP备17019029号-2   Powered by saa

© 2024  Fuzhou Zhuokai Electronic Technology Co., Ltd

闽ICP备17019029号-2  Powered by saa

卓凯电子